ObsidianWire Custom HSH for Strat

The ObsidianWire HSH Wiring Harness for Fender® Stratocaster®, is the perfect way to open up your humbuckers with some extra clarity and output, while retaining that sweet single coil tone.

The trouble with a traditional wiring kit in a Strat® with humbuckers and single coils is that humbuckers need a good 500k potentiometer for full clarity and output, while the single coils need a 250k set of tone and volume controls to tame some of their natural highs.

ObsidianWire is the perfect solution with a special custom design allowing for auto switching between 500k tone and volume controls in the full humbucker positions, and 250k controls for the single coil positions.

The ObsidianWire HSH Wiring Harness

– Auto switch between 500k & 250k tone and volume controls

– 500k For the Humbuckers (Full Output & Clarity)

– 250k for the Single Coil (Traditional Strat Tone)

– Auto Split Humbuckers in Positions 2 + 4 (Perfect Strat Quack)

Furthermore, when you move your switch into the mixed pickup positions the humbucker coils split (requires four conductor humbuckers), with one of them pairing up with the middle pickup for traditional Strat tone.

 

Compatibility:

Note: If Converting to HSH // Humbucker body routes & Pickguard Required

American and Mexican series Fender® Strat® – Direct Fit // Right Hand Guitar Only

Japanese Fender & Squiers® – You will need to widen the control holes out to 10mm and get new US Spec, 24 spline knobs to fit the higher grade electronics. // Right Hand Guitar Only

Other Models – We cannot guarantee that these will fit any other guitar.

Left Hand Guitars – Does NOT Fit

99.00

8 in stock

Description

The ObsidianWire HSH Wiring Harness for Fender® Stratocaster®, is the perfect way to open up your humbuckers with some extra clarity and output, while retaining that sweet single coil tone.

The trouble with a traditional wiring kit in a Strat® with humbuckers and single coils is that humbuckers need a good 500k potentiometer for full clarity and output, while the single coils need a 250k set of tone and volume controls to tame some of their natural highs.

ObsidianWire is the perfect solution with a special custom design allowing for auto switching between 500k tone and volume controls in the full humbucker positions, and 250k controls for the single coil positions.

The ObsidianWire HSH Wiring Harness

– Auto switch between 500k & 250k tone and volume controls

– 500k For the Humbuckers (Full Output & Clarity)

– 250k for the Single Coil (Traditional Strat Tone)

– Auto Split Humbuckers in Positions 2 + 4 (Perfect Strat Quack)

Furthermore, when you move your switch into the mixed pickup positions the humbucker coils split (requires four conductor humbuckers), with one of them pairing up with the middle pickup for traditional Strat tone.

 

The Custom HSH Controls:

1: Bridge Humbucker in Full Mode (500k controls // Rear tone control)

2: Bridge Humbucker in Split mode* + Middle Pickup (250k Controls // Front tone control)

3: Middle Pickup (250k Controls // Front tone control)

4: Neck Humbucker in Split mode* + Middle Pickup (250k Controls // Front tone control)

5: Neck Pickup (500k controls // Rear tone control)

 

* Coil Splitting Requires Four Conductor Neck + Bridge Pickups

Crystal Clear Tone

To make your tone crystal clear at lower volumes, there’s an ObsidianWire Custom Spec Treble Bleed Mod included in this package. This prevents tone ‘muddiness’ at low volumes by allowing high frequencies to pass along a separate path to your amp, rather than being stopped short by the increasing resistance at the volume control.

Components:

ObsidianWire Custom Select Pots (Crafted by CTS) (+/-8%) US Spec Split Shaft / 24 Spline

ObsidianWire / Schaller Propriety Switch (Requires Metric Tip)

Genuine Switchcraft Output Jack

ObsidianWire Custom Select 150 Series Polyester Film Capacitors (+/-5%)

ObsidianWire Premium Selected Volume Mod / Treble Bleed – Improved Volume Taper & Clarity

Easy to Follow Install Manual

 

Compatibility:

Note: If Converting to HSH // Humbucker body routes & Pickguard Required

American and Mexican series Fender® Strat® – Direct Fit // Right Hand Guitar Only

Japanese Fender & Squiers® – You will need to widen the control holes out to 10mm and get new US Spec, 24 spline knobs to fit the higher grade electronics. // Right Hand Guitar Only

Other Models – We cannot guarantee that these will fit any other guitar.

Left Hand Guitars – Does NOT Fit

Reviews

There are no reviews yet.

Be the first to review “ObsidianWire Custom HSH for Strat”
Close ✕